Phenotractor Protocols
Last updated
Last updated
Authors: Matthew Maimaitiyiming, Wasit Wulamu, and David LeBauer
Center for Sustainability, Saint Louis University, St. Louis, MO 63108
This document provides a brief summary of methods, procedures, and workflows to process the tractor data.
Content modified from Andrade-Sanchez et al 2014.
Tractor
Sensors
Sonar Transducer
GreenSeeker Multispectral Radiometer
Infrared Thermal Sensor
The Tractor-based plant phenotyping system (Phenotractor) was built on a LeeAgra 3434 DL open rider sprayer. The vehicle has a clearance of 1.93 m. A boom attached to the front end of the tractor frame holds the sensors, data loggers, and other instrumentation components including enclosure boxes and cables. The boom can be moved up and down with sensors remaining on a horizonal plane. An isolated secondary power source supplies 12-V direct current to the electronic components used for phenotyping.
The phenotractor was equipped with three types of sensors for measuring plant height, temperature and canopy spectral reflectance. A RTK GPS was installed on top of the tractor, see the figure below.
The distance from canopy to sensor position was measured with a sonar proximity sensor ($S\rm{output}$, in mm). Canopy height ($CH$) was determined by combining sonar and GPS elevation data (expressed as meter above sea level). An elevation survey was conducted to determine a baseline reference elevation ($E\rm{ref}$) for the gantry field. CH was computed according to the following equation:
where $E_rm{s}$ is sensor elevation, which was calculated by subtracting the vertical offset between the GPS antenna and sonar sensor from GPS antenna elevation.
An Apogee SI-121 Infrared radiometer (IRT) sensors were used measure canopy temperature and temperature values were recoded as degree Celsius (°C).
Canopy spectral reflectance was measured with GreenSeeker sensors and the reflectance data were used to calculate NDVI (Normalized Difference Vegetation Index). GreenSeeker sensors record reflected light energy in near infrared (780 ± 15 nm) and red (660 ± 10 nm ) portion electromagnetic spectrum from top of the canopy by using a self-illuminated light source. NDVI was calculated using following equation:
Where $\rho\rm{NIR}$ and $\rho\rm{red}$ and ρ_red represent fraction of reflected energy in near infrared and red spectral regions, respectively.
Georefencing was carried out using a specially developed Quantum GIS (GGIS, www.qgis.org ) plug-in by Andrade-Sanchez et al. (2014) during post processing. Latitude and longitude coordinates were converted to UTM coordinate system. Offset from the sensors to the GPS position on the tractor heading were computed and corrected. Next, the tractor data, which uses UTM Zone 12 (MAC coordinates), was transformed to EPSG:4326 (WGS84) USDA coordinates by performing a linear shifting as follows:
Latitude: $U_y = M_y – 0.000015258894$
Longitude: $U_x = M_x + 0.000020308287$
where $U_y$ and $U_x$ are latitude and longitude in USDA coordinate system, and $M_y$ and $M_x$ are latitude and longitude in MAC coordinate system (see section on geospatial coordinate systems). Finally, georeferenced tractor data was overlaid on the gantry field polygon and mean value for each plot/genotype was calculated using the data points that fall inside the plot polygon within ArcGIS Version 10.2 (ESRI. Redlands, CA).
Andrade-Sanchez, Pedro, Michael A. Gore, John T. Heun, Kelly R. Thorp, A. Elizabete Carmo-Silva, Andrew N. French, Michael E. Salvucci, and Jeffrey W. White. "Development and evaluation of a field-based high-throughput phenotyping platform." Functional Plant Biology 41, no. 1 (2014): 68-79. doi:10.1071/FP13126
